part no./ ?? 05w58 0ew6 c ? features/ z single color/ z high bright output/ z low power consumption/ ? z high reliability and long life/ ??? ? descriptions/ z dice material/ ?? ingan z emitting color/ ? super bright white/ ?? z device outline/ ? 5mm round type/5mm ? z lens type/ ? water clear/ ?? note/ ? : z all dimensions are millimeters/ mm z tolerance is +/-0.25mmunless otherwise noted/ ???? 0.25mm ma x cathode ? directivity / ?? relative luminous radiation angle/ ? t a = 25c if=20ma di rectivity/ ? 90 60 30 0 0 0.5 1.0 1.0 0.5 30 60 90 0 led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 1 of 8 www.ledz.com
part no./ ?? ? absolute maximum ratings/ ? ta = 25 value ? parameter symbol test condition min. max. unit reverse voltage ? v r i r = 30 a 5 -- v forward current i f ---- ---- 120 ma power dissipation ? pd ---- ---- 0.4 w pulse current ? ipeak duty=0.1ms 1khz ---- 200 ma operating temperature ?? topr ---- -40 +85 storage temperature ?? tstr ---- -40 +100 ? electrical and optical characteristics / ta = 25 value ? parameter symbol test condition min. typ. max. unit forward voltage ? v f i f = 100ma ---- 3.2 3.4 v reverse current i r v r = 5v ---- ---- 30 a luminous intensity ? i v i f = 100ma ---- 22 ---- lm viewing angle ?? 2 1/2 i f = 100ma ---- 75 ---- deg. color temperature ? cct i f =100ma ---- --- cct bins/ ?? ta = 25 bin w4 w5 w6 w7 w8 w9 min 4500k 5000k 6000k 7000k 8000k 10000k max 5000k 6000k 7000k 8000k 10000k 15000k 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 2 of 8 www.ledz.com
part no./ ?? ? typical electrical/optical characteristic curves/ ? relative luminous intensity ambient temperature t a ( ) -40 0 20 0 0.5 1.0 1.5 80 90 6040 2.0 2.5 -20 fig.3 vs. ? fig.4 vs. ? fig.2 vs. fig.1 vs. ? 400320 2.0 1.5 1.0 2.5 80 120 0.5 24016080 0 0 4.0 0 3.22.8 2.4 3.6 80 forward voltage(v) luminous intensity relative value at if=20ma forward current(ma) if-forward current (ma) 100 80 40 60 40 20 0 0 ambient temperature t a ( ) forward current(ma) 40 120 160 200 ta=25 700 650 600 550 500 450 1.2 0.8 1.0 0.2 0.4 0.6 400 0 wavelength (nm) relative luminous intensity fig.5 vs 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 3 of 8 www.ledz.com
part no./ ?? ? relibility analysis/ ? the reliability of products shall be satisfied with items listed below/ ???? ? confidence level:90% ltpd :10% z test items and results/ ? no. item/ ? test condition/ time/ ? q?ty/ standard/ 1 resistance to soldering heat / tsld=235 5 5 sec 3mm from the base of the epoxy bulb 1 time 25 all pass 2 solder ability/ ? tsld=235 5 5 sec 1times over 95% 25 all pass 3 temperature cycle/ ?? -40 D 100 30min ~ 30min the cut is not more than 2 min 50cycles 100 all pass 4 high temperature /high humidity / ?? 85 / 85%rh 1000hrs 100 all pass 5 high temperature storage / ta=100 1000hrs 100 all pass 6 low temperature storage / ta=-40 1000hrs 100 all pass 7 dc operation life / if=100ma 1000hrs 25 all pass z criteria for judging damage/ ?? criteria for judgement / ?? item/ ? symbol/ test conditions / min./ ? max./ ? luminous intensity/ iv if=100ma iv*0.7 / forward voltage/ ? vf if=100ma / u.s.l*1.1 reverse current/ ir vr=5v / u.s.l*2 *u.s.l. upper standard level / *l.s.l. lower standard level / 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 4 of 8 www.ledz.com
part no./ ?? p/n rank / / qty pcs qc date lot no ? label form specification / ??Z p/n: customer's production number/ ? qty: packing quantity/ ? ranks: iv / vf / wd iv iv rank/ ? vf vf rank/ ? wd color group/ ?? qc: quality control chapter/ date: mm / dd / yy mm month/ dd date/ ? yy year/ ? lot no: production batch number/ ? lead forming / 1. any lead forming or bending must be done before soldering. ???? 2. when forming leads, there must be a minimum of 2mm clearance between the base of the led lens and the lead bend. ? 2 ??? 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 5 of 8 www.ledz.com
part no./ ?? 3. avoid bending the leads at the same point more than once. ?????? 4. during assembly onto pcb, the lead pitch of the led must match the pitch of the mounting holes on the pcb during component placement. ??b????? 5. recommendations for manual plug-in operation, if r eally need taping machine for inserting operation, please make small batch prenatal confirmation. ????????? ? soldering condition / careful attention should be paid dur ing soldering. when soldering, leave more then 2mm from solder joint to case, and soldering beyond the ba se of the tie bar is recommended. ?????? led ?? 2mm ? avoiding applying any stress to the l ead frame while the leds are at high temperature particularly when soldering. led ??????? recommended soldering conditions/ ? : hand soldering ? dip soldering temp.at tip of iron ? 300 max.(30wmax.) ? 300 ? 30 ? preheat temp. ?? 100 max. (60 sec max.) ? 100 60 ? soldering time ? 3 sec max. ?? 3 bath temp. ? 260 max 260 . distance 2mm min.(from solder joint to case) 2 ??? bath time. ? 3 sec max. 3 distance 2mm min 2 . 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 6 of 8 www.ledz.com
part no./ ?? ? cleaning / ? 1. do not clean leds with water, alcohol are re commended solvents for cleaning. when using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. ?????t????????????? 2. leds may be damaged by ultrasonic-washed. before cleaning, a pre-test s hould be done to confirm whether any damage to the leds will occur. led ??????????? ? storage / 1. environmental temperature: -40 ---100 , recommended: -20 ---50 ?? -40 ---100 ?? -20 ---50 2. environmental humidity: 30%---70%, recommended: 40%---60% ?? 30%---70% ?? 40%---60% ? static electricity / 1. static electricity or power surge will damage the led. it is recommended that a wrist band or an anti-electrostatic glove be used when handling the leds. ? led ??? 2. all production machinery and test inst ruments must be electrically grounded. ??? 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 7 of 8 www.ledz.com
part no./ ?? 3. maintain a humidity level of 50% or higher in production areas. ???? 50% ?? 4. use anti-static packaging for transport and storage. ??? ? notes / ? 1. this datasheet will be update re gularly, if there comes out any cha nges, pls confirmed by the latest datasheet. ????? , 1?? 2. when using this product, please observe the abso lute maximum ratings and the instructions for using outlined in these specification sh eets. hb assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these sp ecification sheets. ????????????? ?????????? 05w58 0ew6 c led specification hebei i.t. (shanghai) co., lt d. rev b/3 page: 8 of 8 www.ledz.com
|
